Leading 10 usual forklift crashes ， forklift procedure need to take notice of these issues ！.

Do not ignore the forklift at the workplace. If the operation is not good, there will be major mishaps in minutes, and there are lots of mishaps entailing forklifts.

Instance 1: The forklift freight obstructed the vehicle driver's view, and the individual in front might not be discovered, leading to a moving accident.
Instance 2: In order to keep the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which practically caused casualties.
Case 3: The size of the forklift freight surpasses the permitted width of the route and holds on the roadside rack, which nearly triggers an accident.
Case 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift driver did not see the pedestrian, and the pedestrian did not see the forklift.
Situation 6: The forklift lifts the employees unlawfully, the forklift motorist does not wear the safety belt, the forklift lifter drops and the vehicle driver is squashed when the forklift rolls over.
Instance 7: The forklift motorist did not use a safety belt and fell from the vehicle when it surrendered and was crushed.
Forklift operation need to pay attention to these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after validating that there are no challenges that hinder the safety and security of driving, honk the horn initially and after that begin.
2. For automobiles with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale must be secure before beginning.
3. When the forklift starts with a tons, the driver must first verify that the load is steady and dependable.
4. The beginning must be slow-moving and steady.

Driving.
1. When driving, the elevation in between the bottom end of the fork and the ground ought to be maintained 300mm-400mm, and the mast must be slanted backward. .
2. Do not raise the fork expensive when driving. When going into and leaving the work website or while driving, be careful that there will be no barriers in the sky. When the tons is taking a trip, the fork should not be elevated too high, which will impact the security of the forklift. .
3. After unloading, the fork ought to be decreased to the normal driving position prior to driving. .
4. When transforming, if there are pedestrians or vehicles nearby, the driving signal must be released initially. High-speed sharp turns are restricted. High-speed doglegs will certainly create the vehicle to lose lateral stability and tip over. .
5. When the forklift is downhill, it is purely restricted to switch off the flame and slide, and it is forbidden to brake all of a sudden while driving with tons unless there are unique conditions.
6. When the forklift is running, it must obey the traffic rules in the factory and should maintain a specific safety and security range from the lorry ahead. .
7. When the forklift is running, the lots has to remain in the most affordable position that does not hinder the driving, and the gantry ought to be correctly tilted back. The load shall not be raised except when stacking or loading. .
8. The height of the lots have to not obstruct the vehicle driver's view. In unique scenarios, when the product impacts the forward vision, drive at a low speed when reversing.
9. It is restricted to activate the ramp, neither to drive across the ramp. .
10. The safe driving speed of the forklift in the manufacturing facility location is 5 km/h, and it needs to drive safely at a low rate when going into the production workshop area. .
11. When the forklift is raised, raised or driven, it is prohibited for personnel to stand on the fork to hold things and play a stabilizing role. .
12. If problems are located, they will be repaired and reported in a prompt way, and they will never ever operate with diseases or hide them.

packing and unloading.
1. When fork-loading things, the range between both forks need to be changed as needed to make the lots of the two forks balanced and not manipulated, and one side of the thing must be against the shelf. .
2. It is prohibited to work with a solitary fork or use a fork top or draw. In special conditions, security warning signs have to be set up to advise surrounding pedestrians. .
3. In the process of filling and discharging things, the forklift should be stopped with the brake. .
4. The speed of the lorry must be slow and consistent. Be careful not to roll the wheels on the dunnage, so as not to stretch the rolled things and harm individuals. .
5. When using a fork to fork the goods, the fork must be as deep as possible under the tons, and it needs to be noted that the fork pointer ought to not touch various other goods or items. The lots ought to be supported with minimal back tilt of the gantry to ensure that the lots does not slide backwards. The pole can be slanted forward somewhat when the lots is lowered to enable very easy positioning of the lots and extraction of the forks. .
6. It is prohibited to fork products at broadband and collide with difficult things with the fork head. .
7. When the forklift is functioning, it is prohibited for individuals to loaf the fork, so regarding avoid the collapse of the goods and harm individuals. .
8. Straining is prohibited, and it is restricted to utilize forks to raise employees to take part in high-altitude operations to avoid high-altitude falling mishaps. .
9. It is not enabled to utilize the brake inertia to slide, place, round or roll things. .
10. It is not permitted to use forks to pick, turn pallet unload.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork are in the air. Before leaving the forklift, you need to discharge the goods or reduced the fork framework.
2. Draw the emergency brake take care of to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique scenarios, such as the motorist does not leave the automobile's view and does not surpass 1 min).
4. Eliminate the secret. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the look needs to be examined, and gas, lubricating oil and cooling water should be added.
2. Examine the safety and security efficiency of beginning, running and stopping.
3. Inspect whether the lights and horn signals are total and effective.
4. Throughout the procedure of the forklift, inspect whether the pressure and temperature level are normal.
5. After the forklift is running, the exterior leak ought to also be checked and the seals need to be changed in time.

Forklift Safety Operation Specifications.
1. You should check prior to leaving the auto;.
2. When you come across somebody in front of you throughout driving, you ought to send a signal at a distance of 5 m;.
3. The driving rate in the factory does not go beyond 5 km/h;.
4. When driving, the nadir of the cargo need to be 0.3 m ~ 0.4 m in the air;.
5. The turning need to not be as well sharp to prevent the propensity of " totally free switching";.
6. Running up and down the incline must be slow and consistent, and no turning on the incline is enabled.
7. Do not drive throughout the gradient. When the slope is above 10%, the vehicle needs to be driven backwards when worsening;.
8. When the forklift personnel lug the goods and move forward, if they run into large or hefty goods and most likely to the driver's line of vision, they should take the reversing workout
.
The "Eight Prohibitions" ought to be adhered to in the operation.
1. Single fork procedure is not allowed.
2. It is not enabled to raise the goods for far away driving.
3. It is not permitted to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to straight shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not allowed to utilize inertia pressure to pick up the goods.
6. It is not enabled to utilize stopping pressure to expatriation round or easy-to-roll things.
7. It is not allowed to bring people to service the pallet or fork, and it is purely forbidden to stand under the fork after the fork is increased.
8. Do not drive Stand-on Electric Pallet Stacker side to side on inclines
.
Vehicle parking is not allowed under the list below problems.
1. Curves, narrow roads, railway crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the area with the very same size as Electric Forklift Truck for Warehouse the barrier should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844